Bauma Light S14 Mini Excavator
Mini Excavator mounted Stump Grinder - S14
The S14 skid steer stump grinder is designed to go on both mini skidsteers and mini excavators. With a quick pull of two pins, a standard size skidsteer plate can be put on as well. The direct flow hydraulic drive is designed to provide the best torque and RPM to the cutting head as no flow is diverted to a swing cylinder. The S14 features green carbide teeth which can be rotated three times, letting you grind stumps longer. The unique positioning of the rotor allows the operator an excellent view of the stump grinding action, and the heavy duty fixed deflector safely directs the flow of debris. Cutting depth is up to 10" below ground. The S14’s size makes it ideal for grinding in tight areas, and a great choice for smaller carriers.
Excavator Mount This standard mounting plate is perfect for welding to your skid steer’s unique fitting. |
WEARSHARP® TEETH By Green Manufacturing, Inc. The unique design of the Wearsharp® allows the tooth to retain a sharp cutting surface, unlike traditional teeth that tend to round over. This provides a consistent cut throughout the life of the tooth, allowing you to maintain a faster sweep speed. This round tooth is 3 teeth in 1. Simply loosen the lock nut and rotate the tooth to a fresh, sharp cutting edge. This can be done three times, extending the life of each tooth. |
|
The high number of teeth means that each tooth needs to do less work. Each of the Stump Blasters teeth only need to make a small cut, because the work is shared by more of our rugged teeth they last longer and usually only require 2 or 3 replacements at a time. The bolt-on designed teeth allow for straightforward replacement. |
Hydraulic Motor Skid steer mounted Stump Blasters run on hydraulic motors. For best results, match your equipments flow rate to one of our available hydraulic motor options. |
|
The Stump Blaster’s carbide teeth extend a full 1-¼ inches from the rotor. This prevents chips and mulch from getting plugged. More chip clearing produces smoother operation and reduces heat build-up that can damage the rotor and cause premature tooth failure. |
Rotor The massive ¾" thick steel rotor provides the back bone for the Stump Blaster cutting system. It’s the anchor for the carbide tipped teeth. For smooth operation it’s important that the rotor remains solid, with no flexing. The rugged rotor also provides the Stump Blaster with the extra momentum needed when the grinding is tough, making sure the Stump Blaster can power through the hardest stumps. |
|
Our grease pins are zinc plated to prevent corrosion which will allow for smoother operation of the units joints over their lifetime. |
More Teeth
More Clearance
Greaseable Pins
| Model No. | S14 |
|---|---|
| Baumalight Connection Code | A04 |
| Recommended Carrier Size | 1-2 ton |
| Motor Type | Gerotor |
| Hydraulic GPM | Check Motor Options |
| Rotor Size | 18" |
| Number of Teeth | 12 |
| Tooth Construction | Wearsharp® |
| Cutting Wheel Speed | Depends on GPM |
| Cutting Height - Above Ground | No limit |
| Cutting Depth - Below Ground | 6" |
| Maximum Cutting Depth - Per Pass | 2" |
| Maximum Horizontal Cut | 12" |
| Over Torque Protection | Relieve valve |
| Hitch | 1" pivot pins |
| No. of Remotes Required - Hydraulic | 1 |
| Requires 12 Volt DC | No |
| Unit Weight (Shipping) Lbs. | 394 |
Videos
TOPLINE TRAILERS
1226 County Road 31, Winchester, Ontario, Canada
Phone: (613)-774-0992
Phone: (888)-701-6185
| Monday - Friday | 8:00 am - 5:00 pm |
| Saturday | 8:00AM - 12:00PM |
| Sunday | Closed |
Contact Us
TOPLINE TRAILER
1226 County Road 31, Winchester, Ontario, Canada
Phone: (613)-774-0992
Phone: (888)-701-6185
Hours
Monday - Friday
8:00 am - 5:00 pm
Saturday
8:00AM - 12:00PM
Sunday
Closed
Location
